għan
Tiżgura li l-prodotti tal-kumpanija jissodisfaw ir-rekwiżiti tal-klijenti, jipprovdu bażi għall-ispezzjoni tal-prodott, u jiżguraw il-kwalità tal-prodott.
Skop ta 'applikazzjoni
Dan l-istandard japplika għall-prodotti kollha tal-modulu TFT prodotti minn XX.
Tagħmir għall-Ittestjar
Magna tal-kejl elettrika, apparat tat-test, lenti, lampa fluworexxenti, kaliper vernier
Pjan ta 'teħid ta' kampjuni u ċċekkja l-kundizzjonijiet ambjentali
L-unità tal-manifattura (jew proċess tal-QC) twettaq spezzjoni sħiħa għall-ispezzjoni tad-dehra u t-test tal-prestazzjoni elettrika, u għall-kejl tad-daqs jew spezzjoni speċjali, l-ewwel biċċa ta 'kull mudell hija meħuda bħala kampjun u ttestjata 5pcs.
L-unità ta 'kwalità tkejjel 5pcs għall-ewwel kampjun ta' kull mudell, u tadotta l-pjan ta 'kampjunar ta' darba GB / —2012 ta 'spezzjoni normali għall-ispezzjoni tad-dehra, u l-livell ta' spezzjoni ġenerali huwa II.
| Livell mhux kwalifikat | Livell permess （AQL） | Valutazzjoni kwalifikata tal-istandard tal-kwalità |
| Nuqqas ewlieni | Jekk id-daqs huwa difettuż, 0 jirċievu 1 ritorn | |
| Sottomessi | ||
| totali |
L-eżaminatur jeħtieġ li jilbes ċirku elettrostatiku u tmien kerrikots tas-swaba 'fuq iż-żewġ idejn. Jekk huwa LCD mingħajr polarizzatur imwaħħal, is-swaba' kollha għandhom jilbsu kerrikots tas-swaba '.
L-eżaminatur jista 'jiċċekkja viżwalment jew iqabbel mat-tabella tal-paragun tal-film.
Jekk jogħġbok irreferi għall-kampjun għat-test elettriku billi tuża apparat tat-test u display screen.
Id-distanza bejn għajnejn l-ispettur u l-prodott hija 30 ~ 40 cm. L-angolu tal-vista tal-ispezzjoni huwa ta '± 15-il grad fuq il-wiċċ ta' quddiem tal-pannell tal-wiri vertikali u ± 45 grad fuq il-wiċċ ta 'quddiem tal-pannell tal-wiri orizzontali (ara l-figura hawn taħt)
Dawl tal-ambjent: 800 ～ 1200LUX għal spezzjoni viżwali
Temperatura ta 'l-ambjent: 25 ± 5 ℃
Umdità: 25 ~ 75% RH
Iċċekkja l-oġġett
(1) Definizzjoni ta 'difetti puntwali kkawżati minn pannelli interni.
a) Tikek qawwi: tikek tleqq u ta 'daqs kostanti jidhru fuq l-LCD taħt il-mudell iswed.
b) Tikek skuri: Fl-istampi ħomor, ħodor u blu puri, tikek skuri bl-istess daqs jidhru fuq l-LCD.
c) 2 punti biswit = 1 par = 2 punti.
Uri kontroll
| oġġett | deskrizzjoni | Kwantità aċċettabbli | MAJ | MIN | |
| Punti ewlenin | addoċċ | N≤3 | √ | ||
| Żewġ punti biswit | N≤0 | ||||
| Żewġ punti biswit | N≤0 | ||||
| distanza | Distanza minima bejn żewġ spots qawwi | 5mm | |||
| tikka mudlama | addoċċ | N≤4 | √ | ||
| Żewġ punti biswit | N≤0 | ||||
| Żewġ punti biswit | N≤0 | ||||
| Numru totali ta 'tikek skuri u tikek jleqqu | N≤6 | √ | |||
| distanza | Distanza minima bejn żewġ tikek qawwi (tikek skuri) | 5mm | √ | ||
| Punti ewlenin żgħar | D≤can be ignored，<D≤, N≤4,spacing≧5mmD（Point diameter） | √ | |||
| Show fault | V/H line/line crossover line etc. | Not allowed | √ | ||
| Chromatic aberration, uneven; ripple; hot spot | Pass 5% filter under 50% dark light | Invisible, can be judged by limit sample if necessary | √ | ||
*Note: Defects on the black matrix (outside the active area) are not considered defects
Visual inspection
| oġġett | deskrizzjoni | Kwantità aċċettabbli | MAJ | MIN | |
| Point defect (display and appearance) | Black spots, white spots, bright spots |
D≤ignorable, <D≤, N≤4, spacing ≥5mm (Figure 2) | √ | ||
| Bad linearity (display and appearance) | Black line, white line, bright line  |
W≤ignorable, <W≤,L≤, N≤4, | √ | ||
| Polarizer defect | Dents, bubbles | D≤ignorable, <D≤, N≤4, | √ | ||
| Scratch | W≤ignorable,<W≤,L≤, N≤4 | √ | |||
| Panel crack |  |
Not allowed | √ | ||
| Damaged TFT non-lead side |  |
The distance between the minimum break point area, d1≧, cannot be ignored; d1<, N≦0d 1: the minimum distance between the break point area and the dot area | √ | ||
| Damaged TFT pin side |  |
The alignment mark is damaged, the damaged angle>90 | √ | ||
| W≦,L is ignored, but the pin cannot be damaged | |||||
| W≦, (D depth)≦1/2 (1 layer glass thickness) | |||||
| Damaged TFT lead side corner |  |
The swastika cannot be damaged. W≦,L≦5mm | √ | ||
| TFT / CF edge burr |  |
d2≦d 2: The distance between the burr and the edge of the TFT | √ | ||
| other | Poor sealing glue | Height: no more than length: no more than 80mm, the sealing glue must completely cover the crystal filling mouth and the penetration depth is greater than | √ | ||
| LCD dimensions | The size refers to the design specification, the tolerance is ± mm, if it exceeds the tolerance range, it is unqualified | √ | |||
| The liquid crystal is not completely poured into the box | Not allowed | √ | |||
| Gas enters the box during crystal filling | Not allowed | √ | |||
| Smudge | Stain that cannot be wiped off is not allowed to have liquid crystal on the surface or in the glass gap | √ | |||
| Module appearance | Newton ring
|
There are Newton rings and interference lines on the touch screen, rejected | √ | ||
 |
The pattern font is clear, the font line becomes thicker or thinner than the normal line width ≤1/3 (and ≤+/), no hyphenation. accept | √ | |||
| Drums on the touch screen | Acceptable without affecting writing | √ | |||
| There are fish-eye bubbles on the surface of the touch screen FILM | According to the inspection standard of the touch screen | √ | |||
| Poor assembly | Module assembly does not match the assembly instructions | Reject | √ | ||
| Poor assembly | The assembly does not meet the process requirements (fixed double-sided tape or shading tape is not attached, etc.) | Reject | √ | ||
| The connection between the components is not strong (the glass is separated from the backlight, etc.) | Reject | √ | |||
| Defects when attaching transfer paper | Insufficient adhesion to tear off the protective film | Reject | √ | ||
| Attach position | Does not meet the specifications, rejected | √ | |||
| Attaching angle | Attached to the edge of the LCD edge angle is greater than ±15 degrees, rejected | √ | |||
| Poor coding | Does not meet the document requirements | √ | |||
| Other items | PCBA, HSC, FPC, backlight, etc. | Refer to "LCM Finished Product Inspection Specification" ~ conduct inspection | |||
Remarks:
1. Ignore any defects on the protective film of the polarizer, such as scratches, bubbles and particles on the protective film.
2. The angle of all damage must be greater than 90 degrees as shown on the right.
3. If the customer has specified requirements according to customer requirements.
